Tyler fence company

Fence Repair in Tyler, TX

Most fence repairs in Tyler come down to posts. A post that was set shallow or rotted at ground level lets a whole section lean, and a spring storm or a falling pine limb finishes the job. We replace the bad posts and damaged sections and leave the sound part of your fence standing, instead of selling you a whole new one.

Replacing a post without losing the section

When a post snaps at ground level, the pickets and rails on either side are often fine. We unscrew the rails from the failed post, dig out the old stub and its concrete, and set a new post in the same spot, or just beside it if the old footing won't come out cleanly. Once the new post has set, the existing section is pulled back to plumb and fastened to it. Swapping a rotted wood post for galvanized steel is a common upgrade at this point, with brackets that let the wood rails attach the same way. Because the new holes are dug with an auger, the job goes on the 811 locate list like any new fence.

Sistering and bracing

Not every weak post has to come out. If a post is sound above ground but cracked lower down, a steel post driven and set alongside it and bolted through can carry the load, which is called sistering. It suits spots where the old post sits against a slab, a tree root or a neighbor's structure and digging it out would do more damage. Leaning sections on otherwise healthy posts can sometimes be pulled back and braced. When too many posts are bad, we say so.

Gates, rails and loose pickets

A dragging gate is usually a loose hinge post or a wood frame that has racked. Re-hanging it on adjustable hinges, adding a turnbuckle brace, or moving the boards onto a new steel frame through our gate service gets it swinging again. Rails that have split at the post get a new rail or a metal rail bracket, and pickets that have worked loose are re-fastened with coated screws, which hold better than the original nails.

Matching an older fence

New pine next to boards that have weathered for years will look bright for a while, whatever we do. Salvaging good pickets from the damaged section and putting the new ones where they show least helps, and a stain across the whole run evens the color, which our staining crew can do once the new wood has dried. Some towns have their own view on this: Lindale expects repairs to match the existing fence's color, material and character.

Storm claims and shared fences

  • Photograph the damage from both sides, wide and close, before anything is moved.
  • Photograph the tree or limb in place, and where it came from.
  • Keep the broken material until your insurer says it can go.
  • Ask us for a written scope listing each post, rail and section replaced.

If the damaged fence sits on the line with a neighbor, Texas law doesn't make them share the repair cost unless they agree, and taking down a shared or attached fence needs their consent or six months' written notice.

What sets the timeline? How many posts and sections are damaged, whether matching material is available, and whether a fallen tree or limb has to come off first.

Frequently asked questions

Can you replace just the posts?
Usually, yes. If the pickets and rails are sound, we can set new posts and re-hang the existing sections on them.
A tree fell on my fence. Can you fix it?
Yes, once the tree or limb is off the fence. We replace the broken posts, rails and pickets and match the rest of the fence as closely as the material allows. Your insurer may want photos before anything is moved.

Often part of the same job

These often come up on the same property, and can be quoted from the same visit:

Free estimate

Tell us about the fence

Tell us where the fence goes and what you have in mind. We’ll call back to set a time to measure.

  • The fence line walked and measured on site
  • A written quote, itemized by material, posts and gates
  • Texas811 called so buried lines are marked before we dig
  • Your survey, HOA and city rules checked before posts go in

Get a fence estimate

Tell us about the job. We’ll call back to set a time to measure.

Or call (903) 560-4422

Got it, thank you.

We’ll call to set up a time to measure. To talk sooner, call (903) 560-4422